Nitrous Pistons - www.Promodzone.com
13 posts - 5 authors - Last post: 2 Feb 2008john. p .clegg wrote: And as for the timing, the spec sheet states I/L 105 ATDC E/ X 110 BTDC I just can't read anything about valve spring pocket . .... Most forged racing pistons you can buy have adequate cut outs but
Cast Pistons | Stock Car Racing Magazine Article at Automotive.com
PATRICK RACING . PISTONS BY JE®. FEATURES LARGER AND DEEPER VALVE POCKETS / FOR LARGER CAMS AND VALVES. FORGED PISTONS . KITS COMPLETE WITH (2) PISTONS ;
Piston to valve clearance : V-Twin Forum: Harley Davidson Forums
25 Aug 2005 Note: Odyssey pistons do not have clearance to fit large 36mm J32A2 (intake) valves. Solution - custom job to increase valve pockets .
What you need to get for a 3.5L Upgrade for a 1999 TL-P - Acura
15 posts - 8 authors - Last post: 23 Nov 2007This a a REAL custom made racing piston for a diesel engine. Higher lift cam , deeper valve pockets and maintaining the correct bowl shape. .... Brian P . 2006 Jetta TDI 5-sp, Spice Red, Unitronics stage 1,
Cast Pistons - Pistons For Budget Classes - Stock Car Racing Magazine
MPS Racing : JE Custom Hayabusa 85mm Offset Valve Pocket Pistons . Published on September 4, 2010 by Doug Ray · 2 Comments Share to->
332-428 Ford FE Engine Forum: PISTONS
Some valve pockets are cut with one continuous pass across the piston that gives the Todd Higdon Racing Budget Financial Success - Fun And Profit
MPS Racing : JE Custom Hayabusa 85mm Offset Valve Pocket Pistons
Patrick racing High compression pistons have been the reference standard for .... These 10.25:1 forged pistons come with deeper valve pockets to work with
PISTON KITS: Cams, Chains, Pushrod Tubes & Piston Kits
Pat is the crew chief for Dyson Racing , reigning Grand-Am Sports racing ..... Of course you will then have to cut valve pockets in the piston and sink the
Patrick Racing Pistons Valve Pockets
Forged piston kits made for Patrick Racing by JE Pistons ; Kits come complete with Larger and deeper valve pocket for bigger valves and high lift cams
Q420 cams ... : Elans
Forged piston kits made for Patrick Racing by JE Pistons Kit comes complete
Note
15 posts - 6 authors - Last post: 9 Jan 2008I was wondering if ross racing pistons were good?and what compression so if you have a set made be sure to get your valve pockets right.
Head-Block version - Pattakon Greece
Forged piston kits made for Patrick Racing by JE Pistons Kit comes complete with rings, wrist pins and clips 101mm big bore Larger and deeper valve pocket
pistons - Performance Probe Forum
17 posts - 8 authorsAs Carl pointed out, you're also raising the valve pockets . .... Pat Kelley 66 El Camino, daily driver We have gotten a few used rotators from Joe Gibbs Racing and Hendricks as they are the old piston guide rod set up and I have
Tips on buying Custom Pistons for your 308 - Updated January 2011
9 posts - 1 author - Last post: 20 Jan 2009I have an TC88 , I'm going to 95" I have patrick racing team heads that the valve pockets in those pistons are set out for big valves.
15:1 or How low can you go...? - Page 6 - TDIClub Forums
9 posts - 5 authors - Last post: 29 Dec 2009If it touched the valves it could be that the valve pockets on the pistons are off a little. With a big dome and a fast ramp on the opening